Forumsee logo
Forumsee » Motorbikes » Brands & Models

Messages labeled as 'Buell'

1 2 3 4 5 6 7 Next >>   25 50 75

Today

My coker 16 inch tires are starting to get real thin time for new tires. I will mount them on my own in my garage. I figure it will be a lot easier if I take the rear brake drum...

Yesterday

I would like to put chrome fin trim on the cyl jugs of my 1989 1200 Sportster. does any one know if they are available from any supplier? Thanks Jim

2 days ago

the 82 prime cover seems to have striped the threads for the cable adjuster. would a heli-coil insert be a good repair or replace the cover? I ordered up a gasket and ...
I'm looking for solutions/advice, possibly pictures. I changed tires on my 1200n. 21" up front, same 16" on rear, only the tire is a lot more narrow than stock. I'm not digging...
Have a new Sporty that I'm having trouble with. Runs and sounds good.......when I can get it started. Guy I bought from is an old school Harley guy, had them since he was a teen...
OK, so I did search on this and really am more confused than when I started. As some know, my 1995 XLH1200 (with 89" Stroker) is going through a complete rebuild. I have p...
Hi Guys, Working on the brakes at the moment. Just trying to get them as good as I can. I?ve read the threads in the stickies, all really helpful. One of the shoes is ...
I was thinking about installing a cv carb . I have one thatI removed from a Buell.Is there much of benift? What would be a good starting point for jetting ? I live at sea level....
Just got this 1972 XLCH for a winter project. Looks like the engine was rebuilt by a harley guy in town, installed back in the frame and left to sit in a garage. https://...

3 days ago

Hi to all from the other side of the pond has anyone had any experience fitting Balance Masters clutch balancer to an Ironhead. I'm looking for ways to reduce engine vibration ...
I usually only hear about awesome deals people find on some Harley project someone else lost interest in, and this was no different. I was trying to help a guy on Facebook find ...

4 days ago

Hello fellow Sportster enthausiasts,I have recently built a 1979 Sportster. I rebuilt the engine from a box of parts. The motor runs well but I am having trouble with the transm...
Is there a trick to getting the stock slip-ons off or do I have to remove the header as well? Trying to make a set of diy slip-ons and need to remove them for mock up. Had every...

5 days ago

I am curious about street bikes running on etanol and methanol. Methanol gives ofcourse more power but from a future perspective when discussion about loosing the petrol from th...

6 days ago

I was looking at the WERA rule book and noticed that the rules for Vintage 4 list as legal, Evo Sportsters up to 1000cc. Is there a PRACTICAL overbore to get near 1000cc without...
Hi All, 1991 XLH 883 Deluxe. I'd like to remove the speedometer from this bike. To do so, and not chop up the wiring, I'm trying to pull the deutsch socket terminal...
well since the challenge was given, i decided to take up the offer. of course i would use precision equipment, but, i want to show how hilly-billy, redneck or coon ass equip...
Ok I have a 2008 xl1200c. It has short shots with the sensors installed. I'm having trouble with tuning (pc usbIII). No matter what I do I always end up getting a lot of decal p...

7 days ago

Hey everyone ! So recently I was have bad experiences with my 2003 1200c sporty coughing and running a little too rich and so I pulled my cv carb off cleaned it and found a...
Hello guys. I am currently working on a 1969 xlch with S&S super E carb. I am running very rich at a low rpm with jets 66/.265 any thoughts on better jets?

8 days ago

I did a search and didn't see anything for this subject. Is the ignition timing different for a big bore stroker when compared to a stock engine? I bought a 1979 motor built b...

9 days ago

running 202 hustlers now,, super b carb 28 /70 jets,,,,one piece low restrictive pipes ,,,ult ing curve 3,, runs really good..want to try stock p, cams intakes with - - exhau...
Just wondering where most people on this forum order their parts from. I've been using JP Cycles and was wondering if there is a better source, quality / cost? Not that I've had...
I slowly and finally got forward controls for my old 79 Roadster mounted. Naturally it took some horsing around to get them mounted cause they don't make them for that year. An ...
hey xl guys , im currently doing a top end overhaul on my 64xlch and want some more performance i currently have sifton H CAMS ON THE EXHAUST and +H ON THE INTAKES , whats a g...
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

Cafe Racer CBR1000F - Video 2
Cafe Racer CBR1000F - Video 2
This is Fantastic - who'd a thunk it possible?
This is Fantastic - who'd a thunk it possible?
EICMA 2017
EICMA 2017
Sportster Sickness UK is 2 years old
Sportster Sickness UK is 2 years old
ZX12R First In UK News Report
ZX12R First In UK News Report
Hard to know what to make of this!
Hard to know what to make of this!
No! Not another oil thread!
No! Not another oil thread!
TFT screen start up
TFT screen start up

Tags

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more