Forumsee logo
Forumsee » Motorbikes

Messages labeled as 'Buell'

<< Prev 1   ...   4 5 6 7 8 9 10 Next >>   25 50 75

17 days ago

Working on a buddy of mines hardtail Bobber sportster. He hasn't rode it in 5 years or so. He installed a pair of millennium jugs on it and a few miles into a ride it died on hi...
So I have the pc link wire and module on my 2004 sportster 1200. Following jesters instructions. Clear log data I get an error abort ignore retry then cannot establish RS-232 li...
What is the difference between the rear welded steel hub on the 79-81 XL and the rear hub on the Shovel head. V-Twin Mfg lists OEM pm 43540-73A for 73-82 FX It has the two s...
OK, guys...here we go again with the brakes. I bought a '75 that happened to have a '73 front end, but no caliper. I could bite the bullet and buy another front end or just go...
Anyone know the kw output on a stock '07 883 starter? Starting to lose the battle with 210 cranking psi. In retro spec compression releases should have been considered.
Can someone explain to me how/what differences changing from the belt drive to a chain drive would make on Sportster 1200? thanks

18 days ago

Can I easily install a 2017 XL1200X solo seat on a 2015 XL1200X? I know that the rear bracket is different...
OK, newby post done. My bike is an 82 XLS Roadster that my mate has owned for the last 25 years and has been unused for the last ten, It's in good condition and will get som TLC...
Hey guys, I guess this isn't technically and Ironhead question, since it is about painting a motorcycle work table, but since I only plan to use it for working on Ironheads I fi...
As the titles says I suspect a base gasket leak. I am pretty sure the push rod tubes are also staring to weep. It was suggested to me that I try to re-torque the head bolts. ...
Is it possible to remove/ install wheel bearings in my aluminum wheels at home without the H-D tool or am i going to have to take them to a shop to be done?
Hello Everyone, I'm sorry about the long post but I want to give a full background. I have been having some issues with my bike lately & need some advice. The bike has ran...
After a few casual rides with my feet up on the highway pegs, I'm thinking about changing over to forward controls. I was told at one time to avoid a certain style that ha...
Mornin folks.. So I'm rebuilding my engine and have my heads sitting here, which got me thinking about porting/polishing. Now I've read enough to know it can be an awesome...
Hi, I want to change jets and I need to put the enrichener on the top of the manifold to remove the CV. As I know it is delicate, how can be carefully removed from its supp...

19 days ago

i red a dozen times that our bike are supposed to scrapped right and left easily but ive never managed to make it happen ? not sure if my shocks are stock but they look like it ...
2001 883 Hugger.. LONG story short.. I had the detent plate replaced last week. The clip had come un done and the plate was worn. Bike ran like new. Awesome!! After a coup...
Got a set of these further forward mid controls for my 07C with a forward control brake rod that's been cut to match up (the controls come with a brake rod that attaches directl...
I have a 70 xlch900. Will the heads from a 72 early 73 xl fit. I don't know if they are 1000s in those years and even if that makes a difference for the heads.
lost 5th gear on my 2003 883R. i can shift up into 4th, but not into 5th. any help with what might be the issue. also looking for independent shop recommendations. in...
Xl1200s issue when running hammers 1250cc kit ported and Andrews n6 cams can timing be issue. ? 1998 model. Thank you!
Just checking for thoughts and ideas here. I have a 1995 XLH1200 with and S&S 89" stroker kit and the stock carb. When the bike was originally put together, the builder ha...
Failure to pay attention to your roadway Failure to use proper braking Looks like it rotated 180 deg before impact https://www.liveleak.com/view?i=dd6_1501733390
anyone know the size of - footrest assembly retaining ring pn 11304 - clutch lever bolt retaining ring pn 11379 the first it seems to me 8 mm (5/16) the latter it ...

20 days ago

Rode it Monday and it was great. Yesterday I swapped my Arlen Ness a/c for my DK but didn't test ride. Go to ride it tonight, fires up just fine, idles fine, go to pull away and...
<< Prev 1   ...   4 5 6 7 8 9 10 Next >>   25 50 75
 

Last videos:

Anyone want to take their GS to a MX track?
Anyone want to take their GS to a MX track?
Merlin V 1650
Merlin V 1650
What about this Bike...
What about this Bike...
Found some 2018 Harley vids
Found some 2018 Harley vids
Found some 2018 Harley vids
Found some 2018 Harley vids
Found some 2018 Harley vids
Found some 2018 Harley vids
Found some 2018 Harley vids
Found some 2018 Harley vids
Awesome street glide
Awesome street glide

Tags

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more